Sheet begins
DWG IST · Capabilities · Rev. 02 · Scale 1:1
- Subject
- Capabilities
- Entry
- A—02
- Programmes
- 25/26
- Sectors
- 4
- Drawing
- 1:1 · Rev. 02
Integration
Turnkey systems and installations, from rack drawers to complete cabinets, including harness design and manufacture, data acquisition and processing systems, and the operating software — FPGA and microcontroller firmware included.
What it covers
Covers build and assembly: electronic boards, custom harnesses, power distribution units, mechanical assemblies, FPGA and microcontroller firmware, operating and acquisition software. It applies both to the complete system — rack drawer or full cabinet — and to a single subcomponent to be integrated into a third-party bench already in service.
What it leaves behind
It leaves the physical system and what comes with it: a bill of materials updated to the shop-floor changes, cable schedules and as-built harness drawings, the released firmware and software version, an integration record. This is where the design stops being a document and becomes an object that can be measured.
Where it ends, where the next one starts
It begins once the drawings are approved and the components procured, and ends when the system is assembled, powered and ready for the test campaign. The tests that follow do not belong to this phase: they are acceptance testing, and they stay separate so that the result is stated by a procedure written beforehand, not by whoever built the system.
Evidence in the portfolio
Documented by 25 programmes out of 26 published.
This list is not written by hand: it is derived from the “Work performed” entries of the programme cards. Next to each title is the line that matched the programme, so the match can be checked — and disputed. A new card joins on its own.
P—01
Universal work-holding fixture for helicopter blades
Mechanical, electronic and software development
P—02
Communication SCOE for a satellite payload, accepted in factory and on site
Support to system and subsystem hardware and software design
P—03
Interface adapter between an existing test bench and an orbital module
Rack mechanical and electronic development
P—04
Rack tool for revalidating the electrical interfaces of a launch bench
Rack mechanical and electronic development
P—05
Launcher control bench
System and subsystem hardware integration
P—06
Cabinet for an observation payload data chain
Harness design and realization
P—07
RF check-out suitcase for a satellite payload
System design and development, hardware and software
P—08
Telemetry SCOE for a vehicle control bench
Support to system software design
P—09
Rack telemetry kit for a satellite relay link
Support to system software design
P—10
Vehicle control bench for a European launch vehicle, including cable routing in the launch building
Cabinet integration on benches already in service
P—11
EGSE and SCOE system design for third parties
Custom cable design
P—12
Electrical design and firmware: differential serial switching and radio-frequency detection
Electronic board design and realization
P—13
Bench simulators: pyrotechnic lines and electrical loads
Mechanical and electronic development
P—14
Interface and self-test box for a check-out chain
Mechanical and electronic development
P—15
Telemetry, telecommand and radio-frequency sections of an automatic test equipment
Electronics and software development
P—16
LVDS interface chassis for an on-board memory unit, with clean-room harness
System design and production: drawer and external clean-room harness
P—17
Enclosed CE-marked test benches for railway gearboxes and wheelsets
Control software design and development
P—18
Transportable simulation racks for a launch site
System assembly integration
P—19
Modular rack battery pack charger for a launch vehicle
Rack mechanical and electronic development
P—20
Rack power distribution units, single and dual line
Engineering and production
P—21
Input/output front-end electronics for a payload data chain
Electronic board design and build
P—22
RF switch matrix for a radiometer test chain
Assembly, integration and test (AIT)
P—23
RF switch matrix for a check-out bench
Hardware integration and software development
P—24
Antenna control unit with web interface
Electronics and software development
P—25
Simulation SCOE for a radar payload
Support to system and subsystem hardware and software design
Sheet ends · shell resumes